space:remont
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revision | ||
space:remont [2024/04/30 11:19] – woju | space:remont [2024/05/18 12:33] (current) – [welding/grinding workshop] pl0myk | ||
---|---|---|---|
Line 23: | Line 23: | ||
5. Podpięcie innego kranu nad zlewem (ask [[people: | 5. Podpięcie innego kranu nad zlewem (ask [[people: | ||
- | 6. Kibel_IoT by [[people: | + | 6. Kibel_IoT by [[people: |
- | |||
- | ==== How to paint: olejna edition ==== | ||
- | |||
- | - Upewnij się że ściany są zagipsowane oraz przetarte [[https:// | ||
- | - Połóż taśmę malarską na odpowiednim poziomie (~150cm, | ||
- | - Znajdź otwartą puszkę z farbą olejną, otwórz ją pomarańczowym śrubokrętem standard (płaskim) - powinien znajdować się w niej wałek | ||
- | - Znajdź tackę na farbę z wkładką z wyschniętą farbą olejną (tylko olejną można wiele razy używać!) | ||
- | - Znajdź uchwyt do wałka (prawdopodobnie będzie gdzieś razem z tacką) | ||
- | - Nałóż wałek na uchwyt, nalej farbę na wkładkę na tacce | ||
- | - Maluj, nie wychodząc za taśmę malarską! | ||
- | - Po nałożeniu pierwszej warstwy należy poczekać, aż wyschnie, zanim nałoży się drugą warstwę | ||
- | - Po malowaniu wrzuć wałek do kubła, zostaw tackę i uchwyt do wyschnięcia! | ||
===== Warsztat cieżki ===== | ===== Warsztat cieżki ===== | ||
+ | * electrical wiring must be remade, need more outlets in welding and woodworking zones | ||
* clothes go into a locker to be situated between server room and the rack with museum, where arcade machine currently sits | * clothes go into a locker to be situated between server room and the rack with museum, where arcade machine currently sits | ||
* arcade machine to be exposed somewhere near central column, next to the heavy workshop doors | * arcade machine to be exposed somewhere near central column, next to the heavy workshop doors | ||
- | * in the workshop, draw yellow boxes on the floor marking the width of an europallet (800×1200 mm) | + | * in the workshop, draw yellow boxes on the floor marking the width of an europallet (800×1200 mm) (pl0myks opinion: yellow box minimum width 1000mm wide) |
* curtains dividing welding/ | * curtains dividing welding/ | ||
* keep the specific kind of dust contained to the respective section: wood in wood, metal+oil in metal | * keep the specific kind of dust contained to the respective section: wood in wood, metal+oil in metal | ||
Line 54: | Line 43: | ||
up to about first row of columns | up to about first row of columns | ||
- | * new rack for wooden beams | + | * new rack for wooden beams (done by woju and pl0myk) |
- | * swap wooden sheets | + | |
* dust extractor on the column, hanged from the wall | * dust extractor on the column, hanged from the wall | ||
* horizontal ducts high on the wall, branched to every woodworking machine | * horizontal ducts high on the wall, branched to every woodworking machine | ||
Line 63: | Line 51: | ||
* on wheels, to be moved against the wall when not in use, but possible to move to around the centre of the section and possible go approach from all sides | * on wheels, to be moved against the wall when not in use, but possible to move to around the centre of the section and possible go approach from all sides | ||
* belt grinder will remain in this section, but needs to have water tank in front of it, below the vertical section of the belt, permanently attached (samla on a chair is not enough) | * belt grinder will remain in this section, but needs to have water tank in front of it, below the vertical section of the belt, permanently attached (samla on a chair is not enough) | ||
+ | * move | ||
==== welding/ | ==== welding/ | ||
- | as it currently is, but: | + | as it currently is (already after changes), but: |
- | * wood storage gets moved to the wood shop | + | * extend exhaust |
- | * metal sheets get stacked | + | * make clamps hangers (done by pl0myk) |
- | * cart for short sections | + | |
+ | ==== machine | ||
+ | |||
+ | * avia goes where bridgeport was standing | ||
+ | * PMMA sheets from wood sheet cart go between lasercutter and the leg of the rack (done) | ||
+ | |||
+ | |||
+ | ==== How to paint: olejna edition ==== | ||
+ | |||
+ | - Upewnij się że ściany są zagipsowane oraz przetarte [[https:// | ||
+ | - Połóż taśmę malarską na odpowiednim poziomie (~150cm, | ||
+ | - Znajdź otwartą puszkę z farbą olejną, otwórz ją pomarańczowym śrubokrętem standard (płaskim) - powinien znajdować się w niej wałek | ||
+ | - Znajdź tackę na farbę z wkładką z wyschniętą farbą olejną (tylko olejną można wiele razy używać!) | ||
+ | - Znajdź uchwyt do wałka (prawdopodobnie będzie gdzieś razem z tacką) | ||
+ | - Nałóż wałek na uchwyt, nalej farbę na wkładkę na tacce | ||
+ | - Maluj, nie wychodząc za taśmę malarską! | ||
+ | - Po nałożeniu pierwszej warstwy należy poczekać, aż wyschnie, zanim nałoży się drugą warstwę | ||
+ | - Po malowaniu wrzuć wałek do kubła, zostaw tackę i uchwyt do wyschnięcia! |
space/remont.1714475991.txt.gz · Last modified: 2024/04/30 11:19 by woju