This is an old revision of the document!
Table of Contents
Hacking the Zsun WiFi SD Card Reader
The goal of this project is to learn as much as possible about the Zsun WiFi card reader and run OpenWrt on it to turn it into an awesome wifi device.
People Involved
- emeryth (emeryth at hackerspace.pl) ← contact me about the project
- q3k (q3k at hackerspace.pl)
- informatic (informatic at hackerspace.pl)
State
All the important aspects of hardware are understood.
OpenWrt confirmed working, but no easy way of flashing yet.
Hardware
- AR9331 SoC
- 64MB RAM
- 16MB SPI Flash
- GL827L USB SD Card Reader
The device consists of two PCBs sandwiched together and connected via 8 pins.
The bottom PCB contains only the SD card reader chip and SD slot, it can be safely removed without affecting operation.
Serial Port
The serial console is brought out on testpoints (see pictures). Bitrate is 115200.
Original firmware root password is “zsun1188”
Ethernet Port
There are testpoints for connecting an ethernet port (eth1 of the SoC).
Use a Magjack or similar connector with magnetics.
This port is required for uploading images to u-boot.
USB switch
The device contains a WAS7227Q USB switch, which connects the sd card reader chip to either the USB plug, or the AR9331 SoC.
The switch is controlled with GPIO21. Set pin to LOW to connect card reader to SoC.
GPIO
- GPIO0 - LED
- GPIO18 - card reader reset
- GPIO21 - USB switch
- GPIO22 - card detect
Hardware hacking
If you remove the card reader board you get easy access to one USB port and 3 GPIO pins. Remember that GPIO is 2.5V!
Original firmware
The original firmware is full of holes, including an always on telnet backdoor on port 11880. Source: http://www.zoobab.com/zsun-sd11x-wifi-card-reader
Regular telnet won't work but you can connect using socat:
$ socat - TCP4:10.168.168.1:11880 ������!���� (none) login: root root Password: zsun1188 Welcome to ------- | / /--/ ___ | / | /| \/ _____ --|--| /_____\ |--- --|-- //--/ / / | __|__ | /|\ / \/ /___\ / | ___|___ ___|____ / | \ / / \| 深圳至上移动科技有限公司 Shenzhen Zsun Cloud Technology Co., LTD. www.zsuncloud.com BusyBox v1.01 (2014.12.27-02:50+0000) Built-in shell (ash) Enter 'help' for a list of built-in commands. ~ #
OpenWrt
WARNING Still under development
My OpenWrt port, based on the 15.05 “Chaos Calmer” release:
https://code.hackerspace.pl/emeryth/openwrt_zsun/
This port sticks to the original flash layout.
I've added a few things to this port to make it more usable on the zsun without having to solder.
- Wifi is enabled by default, AP mode, no encryption
- Entering failsafe will run a script that automatically does a factory rest
- The SD card detect pin is registered as a button and will trigger failsafe when inserted/removed during boot
Flashing
Here are some ways you can flash the device:
- Solder on an ethernet jack and flash from the original uboot (hard but safe)
- Reflash the bootloader from the original firmware to one that supports upload over serial (less soldering but fatal if you mess up)
- Reflash the firmware from the original firmware using mtd_write (easy but you have to do it right on the first try)
- Attach a programmer to the flash chip (impossible to mess up)
Flashing with original uboot
Attach an ethernet jack and serial cable, setup a TFTP server on your PC with a static IP 10.168.168.10
Then at the uboot prompt enter the following commands:
tftpboot 80060000 openwrt.bin erase 9f020000 +${filesize} cp.b 80060000 9f020000 ${filesize}
Where openwrt.bin is your rootfs+kernel image (in that order!).