infra:tools:kodakportrait
Differences
This shows you the differences between two versions of the page.
| Both sides previous revisionPrevious revisionNext revision | Previous revision | ||
| infra:tools:kodakportrait [2023/11/01 04:01] – ar | infra:tools:kodakportrait [2024/06/26 17:38] (current) – [Current status] ar | ||
|---|---|---|---|
| Line 1: | Line 1: | ||
| ====== Kodak Portrait ====== | ====== Kodak Portrait ====== | ||
| Despite the name, it's 3d. Despite the vendor/ | Despite the name, it's 3d. Despite the vendor/ | ||
| + | ===== Current status ===== | ||
| + | * configuration still in flux, is editable from the web ui as needed | ||
| + | * not operable; todo: | ||
| + | * < | ||
| + | * Z offset configuration | ||
| + | |||
| ===== General notes/ | ===== General notes/ | ||
| - | * the stock print surface is a mirror. | + | * the stock print surface is a mirror, so try not to break it when removing prints or anything. |
| - | * the stock nozzles aren' | + | * if printing pet-g, wait for the bed to cool down before removing the print, |
| - | * the printer uses 12V PSU, so heating the print surface takes a while | + | * the nozzle on the right (T0; default) is hardened |
| + | * web interface is available at http:// | ||
| * the printer uses the hotend on the right as a Z probe | * the printer uses the hotend on the right as a Z probe | ||
| * the printer has been klipperified (WIP)! stock slicer won't work anymore! | * the printer has been klipperified (WIP)! stock slicer won't work anymore! | ||
| * password for root user is, for now, identical to hswaw wifi password | * password for root user is, for now, identical to hswaw wifi password | ||
| - | * host + printer config | + | * host <del>+ printer</ |
| + | * klipper printer config is here temporarily: | ||
| * don't do Nix things when a print is in progress; overloads the RPI and makes klipper unhappy | * don't do Nix things when a print is in progress; overloads the RPI and makes klipper unhappy | ||
| * takes a while to boot; when it's done you should see [[https:// | * takes a while to boot; when it's done you should see [[https:// | ||
| ===== profile(s) for slicer(s) (WIP) ===== | ===== profile(s) for slicer(s) (WIP) ===== | ||
| ==== PrusaSlicer ==== | ==== PrusaSlicer ==== | ||
| - | Very rudimentary config. | + | Very rudimentary |
| - | {{ : | + | |
| - | (haven't tested with just a single hotend in use, may misbehave, whoops) | + | There's a bed texture and shape included, but they don't get inlined into config; you'll need to set them yourself. Go to " |
| + | |||
| + | When adding profiles for more filaments, you may want to lower the temperature from what you'd probably use on other printers, to compensate a bit for the poor part cooling of this printer. | ||
| + | |||
| + | ==== Other slicers? ==== | ||
| + | When configuring other slicers use this for "start g-code": | ||
| + | < | ||
| + | PRINT_START T0_USED={ is_extruder_used[0] } T1_USED={ is_extruder_used[1] } T0_TARGET_TEMPERATURE={ first_layer_temperature[0] } T1_TARGET_TEMPERATURE={ first_layer_temperature[1] } BED_TEMPERATURE=[first_layer_bed_temperature] | ||
| + | </ | ||
| + | The printer will handle everything on its own through this macro. | ||
| + | |||
| + | This for "tool change" | ||
| + | < | ||
| + | G1 Z{layer_z + 5} F5000 | ||
| + | |||
| + | T{next_extruder} HOT=1 RETRACT=1 | ||
| + | |||
| + | {if layer_num == 0 } | ||
| + | M109 T{next_extruder} S{first_layer_temperature[next_extruder]} | ||
| + | {else} | ||
| + | M109 T{next_extruder} S{temperature[next_extruder]} | ||
| + | {endif} | ||
| + | |||
| + | G1 Z{layer_z} | ||
| + | </ | ||
| + | |||
| + | And this for finishing the print: | ||
| + | < | ||
| + | FINISH_PRINT | ||
| + | </ | ||
| + | |||
| + | Adjust for macro expansion rules of your slicer. As far as I understand, re-creating these in cura-based slicers may not be trivial. | ||
| ===== Hardware documentation ===== | ===== Hardware documentation ===== | ||
| * standard raspberry pi 3b | * standard raspberry pi 3b | ||
| * standard smoothieboard v1 | * standard smoothieboard v1 | ||
| - | * LED driver board connected to the rpi (needs investigating a bit) | + | * LED driver board connected to the rpi (generic 4pin - rgb+ground - pwm-driven ledstrip) |
| * removed most of hotglue as it did not hold the connectors anymore anyway | * removed most of hotglue as it did not hold the connectors anymore anyway | ||
| Line 53: | Line 92: | ||
| ===== TODO ===== | ===== TODO ===== | ||
| - | * solve filament/ | + | * pressure advance calibration |
| - | * moving bambu to the other shelf helped a bit | + | * accelerometer for input shaping |
| - | * fully extending slide-out shelf should actually solve this. | + | |
| - | * obtain second print surface | + | |
| - | * fix camera/ | + | |
| ===== WIP ===== | ===== WIP ===== | ||
| - | This section needs expansion. You can help by prodding my (ar) ADHD brain to do something with it, or pick an item from TODO list yourself. | + | This section needs expansion. You can help by prodding my (ari) ADHD brain to do something with it, or pick an item from TODO list yourself. |
| - | * general usage instructions | ||
| * slicer profiles | * slicer profiles | ||
| - | * [[https:// | + | * obtain second print surface |
| - | * will probably move more of the tool change macros to klipper, to make slicer profile creation easier | + | * pl0myk volunteered for handling |
| - | * calibration, | + | |
| - | * [[https:// | + | |
| - | * didn't boot with impermanence enabled for some reason; will need to investigate that later. | + | |
| - | * ordered properly angled hdmi and microusb adapters. should allow us to rotate the screen right-side-up which will help with screen legibility and allow us to remove software workarounds. | + | |
| - | * The printer is now 300% more gay! | + | |
| - | * The LEDs aren't synced to any action, but " | + | |
| - | * {{https:// | + | |
| ===== DONE ===== | ===== DONE ===== | ||
| - | This section needs expansion. You can help by prodding my (ar) ADHD brain to do something with it, or pick an item from TODO list yourself. | + | This section needs expansion. You can help by prodding my (ari) ADHD brain to do something with it, or pick an item from TODO list yourself. |
| * hardware documentation (what' | * hardware documentation (what' | ||
| * calibration, | * calibration, | ||
| Line 80: | Line 109: | ||
| * fluidd for webui | * fluidd for webui | ||
| * moonraker accessible over network for slicers | * moonraker accessible over network for slicers | ||
| + | * fix camera/ | ||
| + | * solve filament/ | ||
| + | * now on a shelf next to the entrance, between main room and electronics lab | ||
| + | * filament runout sensors - ordered two, will need installing them properly and changing the printer config a bit | ||
| + | * bonus points for making filament a bit easier to insert | ||
| + | * The printer is now 300% more gay! | ||
| + | * Built-in macros change the chamber color at different parts of the print | ||
| + | * Klipper side of the configuration is now done, for the most part | ||
| + | * Moved significant parts of custom g-code in slicers to klipper gcode macros | ||
| + | * Hotends get primed in their respective areas | ||
| + | * converted the printer from 12V to 24V | ||
| + | * rework part cooling; it's abysmal | ||
| + | * https:// | ||
| + | * < | ||
| + | * skewed bed | ||
| + | * the difference between far-left and front-right corners was around 1mm | ||
| + | * {{: | ||
| + | * shimmed the bed enough to reduce the skew to 0.2mm | ||
| + | * {{: | ||
| + | * actual printing area limitations | ||
| + | * embedding the limitations into actual slicer profile is proving to be difficult/ | ||
| + | * visual aids will have to do for now | ||
| + | * {{: | ||
| ===== Preliminary findings ===== | ===== Preliminary findings ===== | ||
| * controlled with a normal rpi3 + smoothieboard combo | * controlled with a normal rpi3 + smoothieboard combo | ||
| Line 101: | Line 153: | ||
| * „Myślę, że w tym przypadku masz do czynienia nie tylko z powierzchnią ataku, ale również z objętością” ~ drozdziak1 | * „Myślę, że w tym przypadku masz do czynienia nie tylko z powierzchnią ataku, ale również z objętością” ~ drozdziak1 | ||
| ===== Resources ===== | ===== Resources ===== | ||
| - | " | ||
| - | |||
| Many resources about the printer from, apparently, its actual vendor: https:// | Many resources about the printer from, apparently, its actual vendor: https:// | ||
| ===== Plans ===== | ===== Plans ===== | ||
| - | Would prefer to keep hardware mostly unmodified, except for following | + | <del>Would prefer to keep hardware mostly unmodified, except for following</ |
| * replace the e3d v6 with e3d revo (and obxidian nozzles) which is almost a drop-in replacement | * replace the e3d v6 with e3d revo (and obxidian nozzles) which is almost a drop-in replacement | ||
| + | * done | ||
| * replace the 12V PSU with 24V | * replace the 12V PSU with 24V | ||
| + | * done | ||
| * add filament runout sensors | * add filament runout sensors | ||
| + | * done | ||
| * buy angled cables and rotate the screen proper way round. | * buy angled cables and rotate the screen proper way round. | ||
| - | * accelerometer | + | * done & undone; viewing angles on the screen are meh; back to rotation hacks |
| + | * accelerometer | ||
| + | * brushes for automated nozzle cleaning | ||
infra/tools/kodakportrait.1698811280.txt.gz · Last modified: 2023/11/01 04:01 by ar