Differences

This shows you the differences between two versions of the page.

--- infra:tools:voron [2026/04/23 20:34] – [Problems/Things to fix] ar
+++ infra:tools:voron [2026/08/08 21:38] (current) – ar
@@ Line 1: / Line 1: @@
 ====== Voron ======
+| Class | Tool |
+| Function | 3d printer |
+| Model | [[https://vorondesign.com/voron2.4|Voron 2.4 350]] |
+| Hostname/web interface | http://voron.waw.hackerspace.pl/ |
+| Currently installed hotend+nozzle | 0.4mm |
 ===== Status =====
@@ Line 13: / Line 20: @@
 ===== Info =====
-donated by [[people:drozdziak1:start|drozdziak]] , mostly assembled by [[people:noisersup:start|noisersup]], trying to be fixed by [[people:gro:start|gro]]
+donated by [[people:drozdziak1:start|drozdziak]] , mostly assembled by [[people:noisersup:start|noisersup]], trying to be fixed by [[people:gro:start|gro]], annoyed [[people:ar:start|ari]] enough to fix the remaining issues.
 How to use..... good question
@@ Line 88: / Line 95: @@
 | ✅  | Assemble broken parts  | 03.07.2025 | 6.07.2025  | Lower chamber fully assembled  |
 | ✅  | Fix speeds  | 03.07.2025 | 11.06.2025  | it's fine |
-| 🔲  | Mount chamber temperature sensor in some logical place  | 03.07.2025 |   |   |
+| ✅  | Mount chamber temperature sensor in some logical place  | 03.07.2025 | 23.04.2026 | Mounted on rear gantry rail |
 | ✅ | Unclog nozzle | 04.07.2025 | 05.07.2025  | cleaning filament fixed it |
 | ⚠️ | Endstop z still triggered after retract | 22.07.2025 | 22.07.2025  | added information how to fix it @gro  |
@@ Line 94: / Line 101: @@
 | 🔲 | Add filter fan to start/end macros | 4.08.2025 |   |   |
 | ⚠️ | Print and mount PEI stop | 12.08.2025 | 21.04.2026 | [[https://github.com/VoronDesign/VoronUsers/tree/main/printer_mods/Itzo1978/PEI_Stop|Link]] \\ Printed both out of PCCF \\ mounted one near the switch \\ the other spot is blocked by nozzle cleaning things |
-| 🔲 | Better Filament sensor mount/better PTFE path | 12.09.2025 | 23.04.2026 | 2026-04-21 - replaced the PTFE tubes with less-restrictive ones \\ 2026-04-23 - filament path starts with the sensor; is now entering  |
+| ✅ | Better Filament sensor mount/better PTFE path | 12.09.2025 | 23.04.2026 | 2026-04-21 - replaced the PTFE tubes with less-restrictive ones \\ 2026-04-23 - filament path starts with the sensor; is now entering from front/top \\ Top-right door hinge is combined with a spoolholder |
 | 🔲 | Thermal expansion calculation | 16.12.2025 |  | [[https://www.klipper3d.org/Bed_Level.html#determining-thermal-expansion]] |
-| 🔲 | Better door mounts | 21.04.2026 |  | Double-sided tape is failing; the doors should be mounted on screws |
+| ✅ | Better door mounts | 21.04.2026 | 29.04.2026 | New [[https://code.hackerspace.pl/ar/objects/src/branch/meow/hswaw-voron-2.4/front-doors.FCStd|door design]] by Ari |
-| 🔲 | Mildly loose power inlet | 21.04.2026 | | either a reprint or a small model modification should be enough |
+| ✅ | Mildly loose power inlet | 21.04.2026 | 24.04.2026 | A tiny bit of CA glue helped |
-| 🔲 | Outdated system and klipper | 21.04.2026 | | currently runs debian 11, and somewhat dated version of klipper \\ Will attempt NixOS-ification and importing into hscloud. |
+| ⚠️ | Outdated system and klipper | 21.04.2026 | | currently runs debian 11, and somewhat dated version of klipper \\ Will attempt NixOS-ification and importing into hscloud. \\ 02.05.2026 - updated klipper as part of toolboard setup |
 | 🔲 | If front Z-towers are noticeably below back towers, quad gantry leveling can fail with \\ ''Probe triggered prior to movement'' | 23.04.2026 | |  |
-| 🔲 | Homing on Z sometimes misses the switch. Higher chances on first homing on boot | 23.04.2026 | |  |
+| ✅ | Homing on Z sometimes misses the switch. Higher chances on first homing on boot | 23.04.2026 | <del>02.05.2026</del> \\ 03.05.2026 | Was caused by toolhead wiring hitting other printer parts. \\ Fixed by installing a toolboard and replacing wiring with CAN \\ Actually fixed by eliminating belt rubbing on X axis plastic |
-| 🔲 | USB port on HDMI screen seems dead | 23.04.2026 | | Reuse HDMI screen from Kodak, and mount it in a bit more permanent manner on top? |
+| ✅ | USB port on HDMI screen seems dead | 23.04.2026 | 04.05.2026 | Reused HDMI screen from Kodak, and mounted it in a bit more permanent manner on top of the left door |
-| ✅  | Max Z too high - the printer makes unhappy noises above Z=290 | 23.04.2026 | 23.04.2026 | Limited Z in config to 290 |
+| ✅ | Max Z too high - the printer makes unhappy noises above Z=290 | 23.04.2026 | 23.04.2026 | Limited Z in config to 290 |
+| ✅ | Hotend power wires are sus | 25.04.2026 | 02.05.2026 | Toolhead wiring replaced with CAN and a toolboard  |
+| ✅ | Uneven belt tensioning | 03.05.2026 | 03.05.2026 | |
+| ⚠️ | Belt rubbed on plastic  | 03.05.2026 | 03.05.2026 | The plastic part was ground down using a belt-grinder, but will need slight redesign and reprint |
 ===== Possible improvements =====