Differences

This shows you the differences between two versions of the page.

--- infra:tools:voron [2026/05/02 17:40] – [Problems/Things to fix] ar
+++ infra:tools:voron [2026/08/08 21:38] (current) – ar
@@ Line 1: / Line 1: @@
 ====== Voron ======
+| Class | Tool |
+| Function | 3d printer |
+| Model | [[https://vorondesign.com/voron2.4|Voron 2.4 350]] |
+| Hostname/web interface | http://voron.waw.hackerspace.pl/ |
+| Currently installed hotend+nozzle | 0.4mm |
 ===== Status =====
@@ Line 13: / Line 20: @@
 ===== Info =====
-donated by [[people:drozdziak1:start|drozdziak]] , mostly assembled by [[people:noisersup:start|noisersup]], trying to be fixed by [[people:gro:start|gro]]
+donated by [[people:drozdziak1:start|drozdziak]] , mostly assembled by [[people:noisersup:start|noisersup]], trying to be fixed by [[people:gro:start|gro]], annoyed [[people:ar:start|ari]] enough to fix the remaining issues.
 How to use..... good question
@@ Line 100: / Line 107: @@
 | ⚠️ | Outdated system and klipper | 21.04.2026 | | currently runs debian 11, and somewhat dated version of klipper \\ Will attempt NixOS-ification and importing into hscloud. \\ 02.05.2026 - updated klipper as part of toolboard setup |
 | 🔲 | If front Z-towers are noticeably below back towers, quad gantry leveling can fail with \\ ''Probe triggered prior to movement'' | 23.04.2026 | |  |
-| ✅ | Homing on Z sometimes misses the switch. Higher chances on first homing on boot | 23.04.2026 | 02.05.2026 | Was caused by toolhead wiring hitting other printer parts. \\ Fixed by installing a toolboard and replacing wiring with CAN |
+| ✅ | Homing on Z sometimes misses the switch. Higher chances on first homing on boot | 23.04.2026 | <del>02.05.2026</del> \\ 03.05.2026 | Was caused by toolhead wiring hitting other printer parts. \\ Fixed by installing a toolboard and replacing wiring with CAN \\ Actually fixed by eliminating belt rubbing on X axis plastic |
-| 🔲 | USB port on HDMI screen seems dead | 23.04.2026 | | Reuse HDMI screen from Kodak, and mount it in a bit more permanent manner on top? |
+| ✅ | USB port on HDMI screen seems dead | 23.04.2026 | 04.05.2026 | Reused HDMI screen from Kodak, and mounted it in a bit more permanent manner on top of the left door |
 | ✅ | Max Z too high - the printer makes unhappy noises above Z=290 | 23.04.2026 | 23.04.2026 | Limited Z in config to 290 |
 | ✅ | Hotend power wires are sus | 25.04.2026 | 02.05.2026 | Toolhead wiring replaced with CAN and a toolboard  |
+| ✅ | Uneven belt tensioning | 03.05.2026 | 03.05.2026 | |
+| ⚠️ | Belt rubbed on plastic  | 03.05.2026 | 03.05.2026 | The plastic part was ground down using a belt-grinder, but will need slight redesign and reprint |
 ===== Possible improvements =====