infra:tools_tokarka
Differences
This shows you the differences between two versions of the page.
| infra:tools_tokarka [2022/02/26 18:05] – created Arsenicum | infra:tools_tokarka [2022/02/26 21:01] (current) – removed Arsenicum | ||
|---|---|---|---|
| Line 1: | Line 1: | ||
| - | ====== Tokarka / metal lathe ====== | ||
| - | |||
| - | Mondiale Celtic 14 rocznik 1986 - http:// | ||
| - | ===== Some technical data & measurements ===== | ||
| - | **Leadscrew pitch / Skok gwintu śruby pociągowej** - 6mm\\ | ||
| - | \\ | ||
| - | **Bolts& | ||
| - | QCTP main – threaded rod 16mm / nut 24 mm | ||
| - | QCTP lock - nut 17 mm | ||
| - | Chuck bolts - nut 17 mm | ||
| - | Compound - nut 17 mm | ||
| - | Follow rest - nut 17 mm | ||
| - | |||
| - | **Headstock / Wrzeciennik** | ||
| - | Taper - short MT5 (hole 44,3 mm length 100 mm) | ||
| - | Through hole - 35 mm | ||
| - | |||
| - | **Tailstock / Konik** | ||
| - | Taper - MT3 (hole 23,8 mm) | ||
| - | 140mm travel | ||
| - | \\ | ||
| - | Height of rotation axis over crosslide - 102 mm\\ | ||
| - | Height of rotation axis over compound - 41,5 mm\\ | ||
| - | Height of rotation axis over tailstock flat way – 185 mm\\ | ||
| - | Height of rotation axis over moving steady mounting holes - 157,75 - 160 mm\\ | ||
| - | |||
| - | **Carriage / suport** | ||
| - | Carriage travel (Z axis) 74,85 mm per rev | ||
| - | Carriage travel - 720 mm | ||
| - | On the lower left of the carriage apron there are 2 m6 holes 35mm apart vertically - mount for chip guard? | ||
| - | |||
| - | **Cross slide** \\ | ||
| - | Cross slide travel - 200 mm | ||
| - | thickness - 35mm | ||
| - | Wysokość klinu cross slide - 12 mm | ||
| - | Crosslide far end width 150 mm, length 300 mm | ||
| - | Crosslide slots: 15 mm width, 90 mm apart, 210 mm long | ||
| - | T-nuts for crosslide: base width 20.9 mm, top width 15 mm, base height 8.9 mm, two tnut slot starting holes fi25mm | ||
| - | Crosslide dial Ф69 mm | ||
| - | Travel (Y axis) 0.18 mm per rev | ||
| - | |||
| - | **Following steady rest** \\ | ||
| - | mounting holes - M10, 92mm apart | ||
| - | |||
| - | **Compound slide / szufladka** | ||
| - | Compound travel - 120 mm | ||
| - | Compound width 93mm, side of toolpost base 95 mm (square) | ||
| - | On the compound two holes 52 mm apart, dia. 6 mm | ||
| - | Toolpost bolt height 110 mm, dia. 16 mm | ||
| - | |||
| - | **QCTP / Imak szybkozmienny** | ||
| - | dovetail 65°, wider(outer) part width 70 mm, from dovetail to main body (' | ||
| - | main body height 76 mm, side length 95 mm | ||
| - | Bolt sticks out for 33mm | ||
| - | Toolholders: | ||
| - | for 25mm - 60hx95lx50d | ||
| - | |||
| - | **Ways / łoże** | ||
| - | Axis 6,4 cm from center of small prism | ||
| - | Szerokość dołka za małą pryzmą 11 mm, szerokość małej pryzmy 16.3 mm, wysokość małej pryzmy 10 mm, od końca małej pryzmy do bliźniego płaskiego łoża 104,5 mm, szerokość bliżniego płaskiego łoża 28 mm. | ||
| - | Czyli: szerokość stałej podtrzymki/ | ||
| - | |||
infra/tools_tokarka.1645898700.txt.gz · Last modified: 2022/02/26 18:05 by Arsenicum