projects:dslam
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revision | ||
projects:dslam [2021/08/31 23:43] – q3k | projects:dslam [2024/04/05 12:22] (current) – [FXS] q3k | ||
---|---|---|---|
Line 7: | Line 7: | ||
=== Access === | === Access === | ||
- | Lab ADSL DSLAM (HiX 5620 A50) can be reached by '' | + | Lab ADSL DSLAM (HiX 5620 A50) can be reached by '' |
=== Downloads === | === Downloads === | ||
Line 17: | Line 17: | ||
YXIK | YXIK | ||
</ | </ | ||
+ | |||
+ | ==== FXS ==== | ||
+ | |||
+ | We have a companion FXS rack device, Audio Codes MP-124D/ | ||
+ | |||
+ | === Components === | ||
+ | |||
+ | * Main MCU: PowerQUICC MPC860PZQ80D4 | ||
+ | * Line interface: 12x PEB3264 and PEB4266 | ||
+ | * Custom ASICs (codecs?): 6x AC482-C (three more footprints unpopulated) | ||
+ | |||
+ | === PSU Recap === | ||
+ | |||
+ | The output smoothing caps on the PSU (APSI-605AC Rev.C) are bad. Here's the values jotted down so that q3k can order some new ones: | ||
+ | |||
+ | ^ Refdes ^ Capacitance ^ Voltage ^ Diameter ^ Height ^ Lead spacing ^ Replacement ^ | ||
+ | | C9, C10, C14 | 470uF | 63V | 16mm | 20mm | 7.5mm | EEU-FS1K471S | | ||
+ | | C15, C17, | 220uF | 100V | 16mm | 25mm | 7.5mm | UHE2A221MHD6TN | | ||
+ | | C19, C20, C22 | 1200uF | 10V | 10mm | 20mm | 5mm | EEU-FS1E122B | | ||
+ | |||
+ | C19 is bulged. C10 is burst. The rest look fine (after desoldering, | ||
+ | |||
+ | There' | ||
+ | |||
+ | === JTAG Pinout === | ||
+ | |||
+ | Refdes J8 ' | ||
+ | |||
+ | ^ Function ^ Pin ^ Pin ^ Function ^ | ||
+ | | Diode | 1 | 2 | Diode | | ||
+ | | Diode | 3 | 4 | GND | | ||
+ | | 3v3? | 5 | 6 | GND | | ||
+ | | Hi-Z | 7 | 8 | GND | | ||
+ | | Hi-Z | 9 | 10 | GND | | ||
+ | | Diode | 11 | 12 | GND | | ||
+ | | Hi-Z | 13 | 14 | Hi-Z | | ||
+ | | Hi-Z | 15 | 16 | Diode | | ||
+ | | Hi-Z | 17 | 18 | Hi-Z | | ||
+ | | Hi-Z | 19 | 20 | Hi-Z | | ||
+ | |||
+ | Diode means a diode was detected (0.3V-1.6V) from that pin to ground. Hi-z means there didn't seem to be a diode between that pin to ground. This looks like a custom JTAG connector, q3k will attempt to discover the pinout once the PSU is fixed. | ||
+ | |||
+ | There' |
projects/dslam.1630453380.txt.gz · Last modified: 2021/08/31 23:43 by q3k