Differences

This shows you the differences between two versions of the page.

--- projects:spoolvault [2024/03/08 00:56] – [Settings] czechu
+++ projects:spoolvault [2024/04/11 09:20] (current) – [BOM] czechu
@@ Line 7: / Line 7: @@
 ====== SpoolVault filament dryer ======
+**Work in progress**
+{{:projects:spool-vault-box.jpg?direct&400|}}
 Large 3D printing filament dryer and storage box, with over the top design specs:
@@ Line 22: / Line 26: @@
 ==== Settings ====
-Most dryers don't go higher then 70°C. We need to develop our own settings after calibrating the heat. Recommendations from manufacturers should help.
+We will develop filament settings after calibrating the heat. **Check filament manufacturer recommendations before drying.** Here is a list of approximate values sourced from resources linked below.
-Resources:
+^ Material       ^ Drying (°C) ^ Duration (h) ^ Printing (°C) ^
+| ABS            | 60-85       | 3-4          | -             |
+| ASA            | 60-80       | 2-4          | -             |
+| HIPS           | 60-80       | 2-3          | -             |
+| PA (Nylon)     | 70-90       | 4-12         | 60            |
+| PETG           | 55-65       | 3-8          | -             |
+| PLA            | 40-50       | 4-6          | -             |
+  * Drying temperature can vary. It's a generic safe value.
+  * Duration: The best method is to observe spool weight. After some time drying stops being effective.
+  * Printing temp: Educated guess. More research needed. Filament will probably cool in the tube between dryer and a 3D printer, but high temperature will prevent it from absorbing moisture while printing.
+=== About overheating and over-drying ===
+Filament can form cracks if dryed too rapidly. If a spool absorbed a lot of water, start with lower temperature and longer drying time. The best approach is to take regular weight measurements while drying.
+Over-drying can result in filament degrading and becoming brittle. Don't exceed manufacturer recommended drying time. It's better to have some moisture then an aged spool.
+=== Research ===
+Useful generic information about polymers: [[https://www.tworzywa.pl/wiedzopedia/baza-tworzyw/|tworzywa.pl/wiedzopedia/baza-tworzyw]]
+Theoretical glass-transition temperature doesn't look relevant for engineering materials. https://forum.prusa3d.com/forum/original-prusa-i3-mk3s-mk3-print-tips-archive/glass-transition-temperatures-not-what-they-seem/
+Most dryers don't go higher then 70°C. Resources:
   * Glass transition temperature table [[https://omnexus.specialchem.com/polymer-property/glass-transition-temperature|omnexus.specialchem.com/polymer-property/glass-transition-temperature]]
@@ Line 31: / Line 59: @@
   * Eibos3D Polyphemus settings  [[https://shop.eibos3d.com/products/pre-order-eibos-3d-filament-dryer-polyphemus|shop.eibos3d.com/products/pre-order-eibos-3d-filament-dryer-polyphemus]]
-=== About overheating ===
-Filament can form cracks if dryed too rapidly. If a spool absorbed a lot of water, start with lower temperature and longer drying time. The best approach is to take regular weight measurements while drying.
+There are industrial dryers that heat up to 150°C:
-Most filaments a spools are made out of PS with glass transition at about 100°C. Let's check the temperature when it starts deforming.
+  * Apium F300; 13 000 zł; Presets visible in the promotional video
+    * https://apiumtec.com/en/apium-f300-filament-dryer
+    * ABS 60°C 4h, Nylon 70°C 10h
+  * Purpose FD5; 3200 €; Manual found online
+    * https://www.igo3d.com/mediafiles/Sonstiges/PurposeAMS/USER%20MANUAL_FD5.pdf
+    * PLA 50°C 4h, PA 65°C 6h
+Filament manufacturers recommendations:
+  * 3DXTECH Filament Drying Recommendations
+    * https://www.3dxtech.com/drying-instructions/
+    * PLA 65 2-4, PETG 65 2-4, FLEX TPC 65 4, NYLON 90 4, ASA 80 2-4, ABS 80 2-4
 ===== Build =====
@@ Line 44: / Line 80: @@
 ==== BOM ====
-  * 🚚 Ammunition Box 47x21x37cm (NATO size 3)
+  * ✔️ Ammunition Box 47x21x37cm (NATO size 3)
-  * 🚚 PTC heater 220V 400W 120x50mm
+  * ✔️ PTC heater 220V 400W 120x50mm
   * 🚚 Thermostat (REX-C100)
-  * 🚚 High temperature fan (from convection oven)
+  * ✔️ High temperature fan (from convection oven)
-  * 🚚 Steel threaded rivets M10 ≥6pcs.
+  * ✔️ Steel threaded rivets M10 ≥6pcs.
   * ✔️ PTFE tubing & couplers
-  * ❔ Alarm light and buzzer
+  * ✔️ Alarm light and buzzer
-  * 🚚 AC IEC socket with power switch and fuse (AC-01-2)
+  * ✔️ AC IEC socket with power switch and fuse (AC-01-2)
   * ✔️ Wire crimper and supplies
@@ Line 58: / Line 94: @@
 Goal is to have a basic version for a price of a cheapest commercial dual-spool drybox. At the time of writing Creality Space Pi can be found on Aliexpress for 366zł.
-I was able to get surplus ammunition boxes for 100zł (~$25). I'm not sure what the best heating solution is yet. PTC heater with automatic shutoff at 150°C and with higher power then other commercial dryers have seems safe. Safer then disassembling a hair dryer. It might be under-powered, we will see. It was cheap, at 52zł. I chose REX-C100 for a PID temperature controller. It's extremely widely used, and it makes it very cheap. 48zł including SRR with radiator and a K thermocouple. Fused IEC socket with rocker switch costs 10zł. I also added optional 2x 220V signal diodes, 7zł. Threaded rivets will make installing ports for printing directly from the box very easy. I got both M4 and M10 from Aliexpress for ~30zł. Convection oven fan with motor is will costs 75zł new, ~50zł used. I opted for a new one named C460002A9. Plus speed controller for 8zł.
+I was able to get surplus ammunition boxes for 100zł (~$25). I'm not sure what the best heating solution is yet. PTC heater with automatic shutoff at 150°C and with higher power then other commercial dryers have seems safe. Safer then disassembling a hair dryer. It might be under-powered, we will see. It was cheap, at 52zł. I chose REX-C100 for a PID temperature controller. It's extremely widely used, and it makes it very cheap. 48zł including SRR with radiator and a K thermocouple. Fused IEC socket with rocker switch costs 10zł. I also added optional 2x 220V signal diodes, 7zł. Threaded rivets will make installing ports for printing directly from the box very easy. I got both M4 and M10 from Aliexpress for ~30zł. Convection oven fan with motor is will costs 75zł new, ~50zł used. I opted for a new one named C460002A9. Plus speed controller for 8zł. Lastly, alarm light/buzzer for 6zł.
-Spent so far: **340zł**. The only thing missing is an alarm light&buzzer - after checking controller voltage.
+Spent so far: **346zł**.
 === How to search for parts ===
 Researching products designed for convection ovens (termoobieg) and DIY meat smoking (wędzarnia) helped. There are no unsolved issues here, just a lot of integration.
 ==== Log ====
   * 2024-03-06 - project started, initial purchase - box i.d. 43.5×37×18.5cm
+  * 2024-03-09 - box has been delivered
 ===== Ideas for improvements =====
@@ Line 74: / Line 113: @@
   * Glass visor
   * Alternative gasket material
-  * Painting inside with heat-resistant paint (is light color an option?)
+  * Painting inside with heat-resistant paint (white 800°C paint)
   * Flament rotation motor (oven roast motor? microwave oven turntable?)
   * Humidity sensor (needs to be temperature resistant)
@@ Line 80: / Line 119: @@
   * Load cell for spools
   * Klipper/printer integration