Differences

This shows you the differences between two versions of the page.

--- infra:tools:tig [2021/01/10 12:31] – nietaki
+++ infra:tools:tig [2024/06/30 14:28] – warning about ⊕ and ⊖ woju
@@ Line 1: / Line 1: @@
+====== FACHOWIEC® Welder's Fantasy® JET TIG II AC/DC 200-S ======
+Webpage: https://welderfantasy.com/?page_id=3146\\
+Manual: https://fachowiec.com/hurt/uploads_pdf/jet_tig_ii_200.pdf
 ====== Basic setup ======
 This is setup that is frequently used and consumables should be stocked in relatively high quantities.
-**Torch**: SR-17\\
+**Torch**: SR-26\\
-**Electrodes**: 2% Lanthanated 1.6 mm (WL20 blue), <del>1.5% Lanthanated 1.6 mm (WL15 gold)</del>\\
+**Electrodes**: 2% Lanthanated 1.6 mm (WL20 blue), <del>1.5% Lanthanated 2,4 mm (WL15 gold)</del>\\
 **Filler rod**: W4Si1/ER70S-6/12.64 1.6 mm - basic copper coated rod for carbon steel\\
 **Torch cups**: 54N14 / 54N16 + 1.6 mm SR17 gas lenses\\
 **Argon gas**: main 40L argon gas cylinder + 8L reserve / portable tank
+<WRAP important>
+⊕ and ⊖ labels for welding cable connectors on the front panel refer to polarity for MMA (+ for stick, - for ground). For TIG welding they're swapped, so the ground cable stays in the same connector. If you keep ground in ⊖, then "DC-" and "DC+" modes work correctly, otherwise they're swapped. Same goes for AC stuff, duty cycle will be inverted if you plug ground to ⊖.
+</WRAP>
 ====== Extended setup ======
@@ Line 16: / Line 25: @@
 ====== In stock =======
-Gold 1.6 / 2.0 / 2.4 electrodes (do not buy - replaced by blue WL20)\\
+Gold 1.6 / 2.0 / 2.4 electrodes (do not buy - replaced by blue WL20 2% Lanthanated)\\
 x 308LSi 1.6 mm TIG rod for welding stainless steel\\
-x AlMg5 1.6 mm TIG rod for welding aluminum (requires AC power supply we do not have)\\
+x AlMg5 1.6 mm TIG rod for welding aluminum\\
 x CuSi3 2.0 mm TIG rod for TIG brazing
 ====== Where to buy ======
 [[https://allegro.pl/uzytkownik/sklepspawacza|sklepspawacza]] - cheap consumables on allegro\\
-[[http://norgaz.pl|Norgaz]] - argon gas, costs about 100 PLN / 40L gas cylinder (shipment included), They accept bank transfers
+[[http://norgaz.pl|Norgaz]] - argon gas, costs about 155PLN / 40L gas cylinder (+30PLN shipment), They accept bank transfers
 ====== Links ======
@@ Line 42: / Line 51: @@
   * As a rule of thumb, the electrode should be sticking out from the ceramic cup by about half of the diameter of the cup's opening.
   * While welding, keep the electrode as close to the material as you can without dipping it into the puddle. 3mm distance is alright.
+  * If you just finished welding a part it might still be very hot even if it's not glowing anymore. If you touch it with your bare hand you might burn yourself
 ====== Keywords ======
 Some of the pages are sometimes hard to find, here's some relevant keywords: spawanie, spawarka, welder, argon